This Wireless Bridge kit includes Two Outdoor Access Points, as well as 100ft. of cat5 network cable.

Features:

AES ENCRYPTED WIRELESS BRIDGE!
Integrated 20db Internal Antenna

Weather Proof Enclosure

Carrier Class QOS with Low Latency

54mbps Transfer Rate

POE and POWER Adapter Included

Status LED's on AP MODE

100ft. of cat5 network cable

VoIP Applications & Streaming Video.

Low Latency (Ideal for Video and Voice)

(For shorter distance, view GNS-1120A)

This Wireless Bridge is a low latency wireless link, that will provide a seamless connection between your two locations.  Low latency is required when VoIP or Video is being streamed across the wireless link.  For a low latency connection, total packet delivery time needs to be 100ms or less.  For voice applications, low jitter is also important.  Jitter is the variation in latency, or the difference between the fastest and slowest packet response times.  This wireless link, will have both qualities, and assuming LOS can connect your locations up to 4 miles.  Contact us for more information.

This Outdoor 20db Integrated Access Point can be mounted outdoors, and can be powered through the integrated Power-over-Ethernet adapter that comes with the unit.  This means that this access point can be placed up to 300ft. away from your network, with only a single cat5 cable connecting to it.  This makes your network Installation easier to install and maintain. Each Access Point will be configured as a Bridge, and will only communicate with each other.  Your wireless bridge can also be configured with AES Encryption, which means a safer, and more secure network connection for your LAN.

This Wireless Bridge is connecting at a frequency above 5Ghz, which means if you have trees or other obstacles in the path of your Point-to-Point connection, you will still have a strong and solid connection.  Simply mount the enclosure outside in the direction of your remote location, connect the cat5 network cable to your LAN, and your ready for connectivity.

VLAN Trunking:  Typically a switch uses port based VLANs.  This means that whatever is plugged in to Port X, belongs to whatever Port X is in.  Each frame is tagged with a VLAN tag in the layer 2 header when entering a VLAN switch port.  These frames run across trunk links between two switches and between a switch and a router.  The tag is stripped down when the frame is sent from the outgoing switch port to the end device.  Remember that the native VLAN frames (by default VLAN 1 in Cisco and many other devices) are NOT tagged.

When you use a radio link, or wireless bridge on a VLAN trunk, there are some things to remember:

• You must use a transparent bridge or the trunk will be unable to form.  Remember, L2.5 bridging rewrites the layer 2 header.  (This bridge operates as a transparent bridge, when in bridge mode)

• The radios included in this wireless bridge (and many other wireless devices) are not switches and are not VLAN aware.  Therefore, tagged frames in the trunk will be ignored by the devices.

• The VLAN tag is 4 bytes long.  This means that the maximum Ethernet frame size goes from 1518 bytes to 1522 bytes.  Any devices on the trunk link needs to be able to pass these frames.  This Wireless Bridge, with up to date firmware can pass VLAN tagged frames.

Ask us about pre-configuration of these Access Points, so they work "out of the box" and ready to install at your two locations.  

Features at a glance

• Dual Ethernet Ports:  This will allow you to daisy chain radios at your installation sites.  This can benefit you as an installer, as the dual Ethernet ports will allow you to plug in PoE devices such as network cameras or other Outdoor Access Points.

• More Robost Routing Features:  Includes Tunneling Protocol Support, which will allow you to pass through VPN clients, as well as use tunneling protocols such as VPN, PPTP, RSA and others.

• All New Access Point Features:  WDS will allow this Outdoor Access Point to be wirelessly connected to other Access Points, while still servicing clients.  (Wireless Distribution System)

• Wi-Fi Protected Access (WPA):  Wireless Protected Access impoves on the security features of WEP.  It includes impoved data encryption and user authentication, and AES Encryption.

• All New Client Adapter Features:  With this Outdoor Access Point, you will be able to align your client and point-to-point installations without having to log into the radio.  You will get visual signal strength at a glance by using this great new feature, using the alignment LED's located on the back of the Access Point.

• Controllable High Gain Output:  Both radios have 13dBm maximum output.  This works great for long distance Point-to-Point applications, as well as Client applications.  Power can be scaled back for closer installations to avoid noise issues and to meet local regulatory requirements.

• Wireless Security:  WEP, WPA wireless security is included in this wireless backhaul.  This will encrypt the data being sent between the connection.  Also included in this wireless backhaul is AES encryption, which is a higher level security feature then standard WEP/WPA.  The two radios can also be configured in PXP mode, which enables only the two outdoor access points to communicate with each other, avoiding any other access to the network.  The wireless bridge operates seamlessly as a Wireless Bridge between your two locations.

• Wireless Interference:  This wireless Ethernet Bridge is operating at 5Ghz.  At most locations, this frequency is used less frequently then the standard 802.11b/g, so interference is usually minimized.  If you experience interference at this frequency, check that your antennas are not mounted directly on a metal surface, have line of sight between each other, and try changing the channel to one that is available .  You may also want to move to a 802.11b/g, 2.4GHz wireless bridge. Click here for an 802.11b/g wireless bridge.

• The GNS-1120P wireless Ethernet bridge radio delivers up to 54 Mbps of sustained data throughput using the 5Ghz Frequency. The IP-native bridge operates in multiple 5 GHz bands, which offers network operators highly flexible choices between multiple frequency bands in the convenience of one radio (5.2 GHz, 5.3 GHz, 5.4 GHz, or 5.8 GHz), and provides improved performance and valuable operational flexibility in high radio frequency (RF) noise floor environments.

Technical Specs.

Specifications are subject to change without notice.

Subject to local regulations.

 

In StockGNS-1120PContact Us to Buy