Mouse over Picture to View Back Panel.

This Wireless Bridge kit includes Two Outdoor NLOS Access Points, as well as 100ft. of cat5 network cable, Power Supply and Mounting Kit.

Features:
Integrated 11db 900MHz Antenna

Weather Proof Enclosure

Carrier Class QOS with Low Latency

54Mbps Transfer Rate at 900MHz

Integrated PoE Adapter included

True NLOS bridging Solution.

100ft. of cat5 network cable included

Perfect Solution for tree penetration

Technical Specs.

Ask us about Pre-Configuration...so your unit

   works right out of the box.

This Outdoor 11db Integrated Access Point can be mounted outdoors, and can be powered through the integrated Power-over-Ethernet adapter that comes with the unit.  If you are looking to connect multiple locations, but have obstructions such as trees in the way, then this bridge kit is the ideal solution.  The outdoor antenna needs only a single Ethernet Cable connected to it, making your installation fast and easy.  Bridge your wireless network together up to 1 mile away, and gain access to sharing files, videos, or other data.

The 900MHz access point can be placed up to 300ft. away from your network, with only a single cat5 cable connecting to it.  This makes your network Installation easier to install and maintain. Each Access Point will be configured as a Bridge, and will only communicate with each other.  This means a safer, and more secure network connection for your LAN.  No other rogue laptop user will be able to pick up the signal between your two points.

This Wireless Bridge is connecting at a frequency of 900MHz, which means if you have trees or other obstacles in the path of your Point-to-Point connection, you will still have a strong and solid connection.  Simply mount the enclosure outside in the direction of your remote location, connect the cat5 network cable to your LAN, and you're ready for connectivity.  This bridge includes security measures of 40 and 128bit WEP, Media Access Control, and WPA.

VLAN Trunking:  Typically a switch uses port based VLANs.  This means that whatever is plugged in to Port X, belongs to whatever Port X is in.  Each frame is tagged with a VLAN tag in the layer 2 header when entering a VLAN switch port.  These frames run across trunk links between two switches and between a switch and a router.  The tag is stripped down when the frame is sent from the outgoing switch port to the end device.  Remember that the native VLAN frames (by default VLAN 1 in Cisco and many other devices) are NOT tagged.

When you use a radio link, or wireless bridge on a VLAN trunk, there are some things to remember:

• You must use a transparent bridge or the trunk will be unable to form.  Remember, L2.5 bridging rewrites the layer 2 header.  (This bridge operates as a transparent bridge, when in bridge mode)

• The radios included in this wireless bridge (and many other wireless devices) are not switches and are not VLAN aware.  Therefore, tagged frames in the trunk will be ignored by the devices.

• The VLAN tag is 4 bytes long.  This means that the maximum Ethernet frame size goes from 1518 bytes to 1522 bytes.  Any devices on the trunk link needs to be able to pass these frames.  This Wireless Bridge, with up to date firmware can pass VLAN tagged frames.

Features at a glance

• Dual Ethernet Ports:  This will allow you to daisy chain radios at your installation sites.  This can benefit you as an installer, as the dual Ethernet ports will allow you to plug in PoE devices such as network cameras or other Outdoor Access Points.

• More Robost Routing Features:  Includes Tunneling Protocol Support, which will allow you to pass through VPN clients, as well as use tunneling protocols such as VPN, PPTP, RSA and others.

• All New Access Point Features:  WDS will allow this Outdoor Access Point to be wirelessly connected to other Access Points, while still servicing clients.  (Wireless Distribution System)

• Wi-Fi Protected Access (WPA):  Wireless Protected Access impoves on the security features of WEP.  It includes impoved data encryption and user authentication.

• All New Client Adapter Features:  With this Outdoor Access Point, you will be able to align your client and point-to-point installations without having to log into the radio.  You will get visual signal strength at a glance by using this great new feature, using the alignment LED's located on the back of the Access Point.

• Controllable High Gain Output:  Both radios have 25dBm maximum output.  This works great for long distance Point-to-Point applications, as well as Client applications.  Power can be scaled back for closer installations to avoid noise issues and to meet local regulatory requirements.

• Wireless Security:  WEP, WPA wireless security is included in this wireless backhaul.  This will encrypt the data being sent between the connection.  Also included in this wireless backhaul is AES encryption, which is a higher level security feature then standard WEP/WPA.  The two radios can also be configured in PXP mode, which enables only the two outdoor access points to communicate with each other, avoiding any other access to the network.  The wireless bridge operates seamlessly as a Wireless Bridge between your two locations.

Specifications are subject to change without notice.

Subject to local regulations.

 

In StockGNS-1130Contact Us to Buy