802.11N, 4.9GHz, 40Mbps Point to Point Wireless Bridge, 23dBi Integrated Panel Antennas, 24dBm TX/RX Power, WPA/WPA2 security, POE/PS included, - Pre-Configured - 2 Mile Complete Link

Manufacturer: GNS Wireless LLC.
Part #
GNS-1171
Special Order
Availability Contact Us
Price $2,129.99
40Mbps, Ethernet Bridge, 23dBi Antennas - 2 Mile - Complete Link
Product Info

Whats included in this point to point link:

2x Outdoor Radios w/ Integrated Patch Antenna
2x Power over Ethernet Injector (PoE)
2x Power Supply
2x 50ft. Shielded cat5e Ethernet Cable
2x Pole Mount Hardware for 1-2" OD mast

Bridge antennas are pre-configured for "out of the box" installation and operation. External Signal LED's will assist with alignment and troubleshooting procedures. Maximum cat5e cable to be used on each end is 250ft. (Shielded cat5e is recommended).  1 year warranty includes technical support.

4.9GHz Point to Point Wireless Ethernet Bridge. Up to 40Mbps Aggregate data rate. 24dBm transmit power with adjustable output for closer installations. Integrated 19dBi panel antenna, external alignment LED's. Includes AES Encryption, Power over Ethernet Injector, 50ft. Sheilded cat5e cables, Power Supplies and pole mount hardware. Link is shipped pre-configured for "out of the box" installation. Complete Link

Connection to Network:

To connect the access point to your network at each location, a single Cat5 Ethernet cable is used.  A 50ft. cable is included for each location.  (If you need more cable, a maximum length of up to 250ft. can be used)  The Cat5 Ethernet cable connects directly from the outdoor access point using a weatherproof grommet,  to an indoor POE (Power-over-Ethernet) injector.  The POE injector plugs into a standard AC outlet for power, and another Cat5 Ethernet cable connects from the POE injector to your network (Router/PC/Switch etc.)

At the MAIN location, you will typically connect to an open LAN port on the back of your existing router, or switch.  At the REMOTE location, you can connect either directly to a PC if you only have a single computer, or you can connect to an indoor wired/wireless router.  This will allow you to run multiple computers over the wireless bridge.

Maximum Range & Interference:

With clear, un-obstructed line of sight between your two locations, a maximum range of 2 miles can be achieved using this link.  Please note that this Point to Point Wireless Bridge operates between 4.94-4.99GHz.  If you plan on installing more then one link at the same location, you want to avoid interference between each Point to Point link by using separate channels. Mount the outdoor access points as high as possible to further avoid any other 4.9GHz interference.

 

Each access point has a 24dBm maximum output power.  This works great for long distance Point-to-Point applications, as well as Client applications.  Power can be scaled back for closer installations to avoid noise issues and to meet local regulatory requirements.

 

For applications that require transfer of very large files, video transmission, or large amounts VoIP (Voice over IP) traffic, it is recommended that you choose a FULL DUPLEX, 5GHz Point to Point link, which will not only avoid all 4.9GHz interference, but offer much faster throughput, and lower jitter rates.  A full duplex, Point to Point Wireless Bridge will also offer lower latency, which increases performance.

Security Features:

This Wireless Point to Point bridge operates as a transparent bridge.  It is similar to an invisible Ethernet cable connecting your two locations.  It includes multiple security options including WEP/WPA/WPA2.  It also has ability to enable MAC address authentication so that only the two access points are able communicate.  You can hide the network SSID, and because the beam width of the antennas is directional, (about 16°) the signal is not being broadcasted in all directions, only in the direction you aim the outdoor antenna.

 

If you have any other questions, please contact our Pre-Sales/Technical Support Dept. at (516) 214-0321.

GNS Wireless has assembled this kit with the components required for a fully configured "out of the box" solution for a wireless point-to-point link.  The IP address for each wireless radio allows you to customize the settings, and view radio configuration tools.

Back to Top
Specs
Antenna Specifications
Frequency Range: 4.94-4.99 MHz FCC
Gain: 19 dBi Directional Patch Antenna
Polarization: Vertical or Horizontal
AZ/EL Beamwidth: 12°/12°
Front to Back Ratio: 26 dB
VSWR 50 Ohm: < 1.5
Power Consumption: 12W
Size: 13" x 13" x 3"
Combined Weight: 8 lbs with radio
Connector: Outdoor RJ-45 All Weather
Mounting Kit/Style: Included: Pole Mount (1" - 2.5" Diameter)
Operating Temperature: -20°C to 60°C
Material: ABS
Additional Features: UV Stabilized
Radio Specifications
Standard Compliance: Proprietary W-Jet protocol (40 Mbps)
Modulation: BPSK, QPSK, 16QAM, 64QAM
Channel Bandwidths: 5/10/20MHz Selectable
Frequency Band: 4.94-4.99 MHz
Data Rate: up to 40Mbps
Output Power: up to 24 dBm - Adjustable
Receive Sensitivity:

-92 to -75 dBm depending on modulation and channel size

Data Security: Hardware based AES
DC Power Input: 9 - 48 VDC Adapter, PoE injector
Max packets per second 50,000 PPS
Packet latency 2 ms (64 bytes packet)
Warranty 1-Year
Back to Top
Accessories
Back to Top